|
|
- Galvanized Stall Doors &
Grill Units -
FREE SHIPPING
to the nearest freight terminal or commercial business address
in the Continental U.S. 48 States * No Miminum Order Required
for Products on this Page.
Toll Free: 1-800-335-1880
Office Hours Monday-Friday 7:00 am - 5:00 pm EST.
Hot-Dip Galvanized Steel
Horse Stalls
Galvanized Stall Doors & Grill Units Economical
and Corrosion Resistant. Hot-dip galvanizing and our NO-WELD
construction insure long-lasting strength and durability!
 Very
practical, rust inhibitive galvanized stalls provide years of
maintenance free use made in the USA. 4 ft. wide grills have 34" high x
1" round tubes inserted, on 4" centers, into channels
top & bottom. Door frame has same 4 ft. wide grill section,
plus two 7 ft. high vertical side channels. Overall outside dimension
of door is 51 in. x 7 ft. high and can be cut down to smaller
width if desired.
Using the 4 ft. sections, any size stalls can be built (8
ft, 10 ft., 12 ft).
Also, odd sizes can easily be cut with a standard hacksaw. Example:
a 12 ft. stall front would require 2 each 4ft. sections and 1
each 51" x 7' door frame. Removable side stall walls can
be made using our 7 ft. long wall channel designed to accept
standard 2 inch lumber (1 1/2 inch thick). Great for Foaling
Stalls!
Perfect For Building New or Remodeling Old Stalls
|
1. Typical Requirements for 12' Stall Front |
2. Typical Requirements for 10' Stall Front |
3. Side Wall Partitions |
| 1 ea CM 52 Standard Grill |
Same as 12 ft. except hack saw 1 ea CM
52 to 2 ft. |
2 ea CM 54 Wall Channels for each partition. |
| 1 ea CM 53 Grill with Opening or CM 52
Standard Grill |
|
Use CM 52 for ventilated partitions. |
| 1 ea CM 50 Door Frame Assembly |
|
(Use 3 Units for 12' Wall). |
| 1 ea CM 84 Door Hardware Kit |
|
|
Note:
All channels are designed to accept standard 2" lumber
(1 1/2" thick). NO LUMBER IS INCLUDED.
Click
Here for Assembly Instructions
Click
Here for Basic Stall Building Guide
 |
Stall Door- 51 inch wide x 7 ft high CM 50 (galvanized
steel framework only, lumber not included) 4 ft. wide grill is
34" high x 1" round tubes inserted, on 4" centers,
into channels top & bottom. Tubes free-float in the channels
for easy replacement and our no-weld construction provides superior
corrosion resistance. (door latch and top brackets not included,
see sliding door hardware kit below)
Color- Silver
$185.00
Click
here to Order On-line
This item can ship to your residence
FREE!
|
 |
Galvanized Stall Grill (4 ft. section) CM 52 4 ft. wide
grill is 34" high x 1" round tubes inserted, on 4"
centers, into channels top & bottom. Tubes free-float in
the channels for easy replacement and our no-weld construction
provides superior corrosion resistance.
Color- Silver
$125.00
Click
here to Order On-line
This item can ship to your residence
FREE!
|
 |
Galvanized Swing-out grill section CM 52H 4 ft grill
section with a swing-out section allows you to create a gossip
door or a swing-out feed door. Tubes free-float on the assembly
for easy replacement and our no-weld construction provides superior
corrosion resistance. Simply leave out four tubes from your grill
and attach the brackets to your lumber.
Color- Silver
$205.00
Click
here to Order On-line
This item can ship to your residence
FREE!
|
 |
Galvanized Stall Grill (4 ft. section) CM 53 4 ft. wide
grill is 34" high x 1" round tubes inserted, on 4"
centers, into channels top & bottom. Tubes free-float in
the channels for easy replacement and our no-weld construction
provides superior corrosion resistance. This grill has a feed
opening measuring 10 inches x 10 inches.
Color- Silver
$125.00
Click
here to Order On-line
This item can ship to your residence
FREE!
|
 |
7 ft. long wall channel CM54. Removable side stall walls
can be made using our 7 ft. long wall channel designed to accept
standard 2 inch lumber (1 1/2 inch thick). Attach the wall channels
to your support posts or walls and slide the lumber into the
channels. Measures 7 ft. long x 1 3/4" wide x 1 1/2"
deep.
Color- Silver
$25.00
Click
here to Order On-line
This item can ship to your residence
FREE!
|
Click
Here for Assembly Instructions
|
Sliding Door Hardware Kit CM 84. Consists of door brackets,
door latch, bottom stay roller assembly, polyethylene roller
system for long life and 8 ft section of enclosed-top track to
keep dust and material from falling into the rollers and jamming
your door.
All mounting hardware included.
$130.00
Click
here to Order On-line
This item can ship to your residence
FREE!
|
Other stall accessories available in our feeder
and waterer sections.
|
